|
|
| |
|
|
| |
ML210A Installation and Settings
Please register your account first to activate your EasyPhone. Just enter www.easy1call.com, login to My Account using your IP Phone# and Password, and complete the profile |
|
|
| |
|
|
|
|
|
| 1. Package Contents |
- Handset
- Handset Cord
- DC-12V Power Adapter£¨Input selection: 110V,220V,110/220V£©
- User's Manual
|
| 2. Component Illustration |
 |
| Figure 1--Front View |
| 1~9 |
Keys number keys |
| * |
* Key |
| # |
Key call out |
| Function Keys: |
| VOL+ |
volume increase |
| VOL- |
volume decrease |
| HOLD |
call keeping |
| PHONEBOOK |
phone book |
| CALL |
call out |
| CLEAR |
clear |
| REDIAL |
redial |
| SPEAKER |
hand free |
| Menu Keys: |
| UP |
page up |
| DOWN |
page down |
| SET/OK |
set/ok |
| ESC |
exit |
|
Figure 2--Side View
1--RJ-45 input port ; 2--Power Port |
 |
| 3. Character Strings |
Corresponding Keys:
| Key |
Characters |
| 1 |
. ,' ? ! " 1 - |
| 2 |
a b c 2 A B C 2 |
| 3 |
d e f 3 D E F 3 |
| 4 |
g h i 4 G H I 4 |
| 5 |
j k l 4 J K L 5 |
| 6 |
m n o 6 M N O 6 |
| 7 |
p q r s 7 P Q R S 7 |
| 8 |
t u v 8 T U V 8 |
| 9 |
w x y z 9 W X Y Z 9 |
| 0 |
( ) @ 0 - * & |
| * |
* |
| '*' can be used as radix point if only numbers are to be input. |
If you need to enter a character, using the keys to enter the character you want. Press the same key repeatedly will change the character. If you need to enter the same character consecutively, press '#' to confirmed the last entry, then press again to enter the next entry.
Example: To enter 'aJtU', press '2555558#88888#' |
| 4. Installation and Settings |
| 4.1 Installation |
- Place your Netphone-ML210A near a power source.
- Plug the RJ-45 connector of the Ethernet 10/100Base-T cable into the Netphone-ML210A's side input port"(1)",and plug the other side into a hub or switch, or wall/ground socket of the structuring cable.
- Plug the accessory power-adapter into the power outlet, then connect the output-plug to power-por " (3)"of the Netphone-ML210A.
NOTE: If the network is without a HUB, the Netphone-ML210A should be connected with other Ethernet equipment (such as XDSL adapter, CABLE modem or PC) by crossing-over cable. Otherwise the direct-connecting cable is applied. |
 |
| 4.2 Settings |
4.2.1 Setting Steps:
If your Netphone account has been set up, please skip the section '5.2.5 Account settings'. |
 |
4.2.2 Dynamic IP Users |
If you need to configure DNS IP
Press SET/OK to enter the submenu and select 'DNS1' by pressing UP and DOWN. Press SET/OK to enter setting menu and configure your DNS2.
If a spare DNS is requested, press SET/OK to enter the submenu and select DNS2 by pressing UP and DOWN; or you may press SET/OK to enter setting menu and configure your DNS2.
If the account information has been set up, you may start using as soon as you plug in. |
| 4.2.3 PPPoE Users' Parameter Settings |
Press 'SET/OK' to enter the main menu, and use 'UP' and 'DOWN' to scroll and select 'TCP/IP Settings'.
- Do not use DHCP
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select 'Use DHCP'. Press 'SET/OK' to enter settings. Input 0 to disable DHCP.
- Use PPPoE
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select 'Use PPPoE'. Press 'SET/OK' to enter settings. Input 1 to enable PPPoE.
- Set PPPoE account
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select 'PPP Identity'. Press 'SET/OK' to enter settings. Continue pressing a number key to change the letter, and press the '#' key to confirm it.
- Set PPPoE Password
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select 'PPP Identity'. Press 'SET/OK' to enter settings. Continue pressing a number key to change the letter, and press the '#' key to confirm it.
- If DNS IP is requested
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select 'DNS1'. Press 'SET/OK' to enter settings and configure your 'DNS1'. If a spare DNS is requested, press SET/OK to enter the submenu and select DNS2 by pressing UP and DOWN; or you may press SET/OK to enter setting menu and configure your DNS2.
NOTE: When you finish setting up, press 'SET/OK' to confirm or 'ESC' to cancel. If you input your setting accordingly, the LCD will display the new setting. Otherwise, the LCD will display 'Input Invalid'; press ESC to return to your previous setting. |
4.2.5 Account Settings |
Press 'SET/OK' to the main menu, use 'UP' and 'DOWN' to select 'Account Settings.
- Set phone number
Press 'SET/OK' to the submenu, use 'UP' and 'DOWN' to select 'Phone Number'. Press 'SET/OK', and then, use 0~9 to input the phone number
- Set user ID
Press 'SET/OK' to the submenu, use 'UP' and 'DOWN' to select 'User Identity'. Press 'SET/OK', and then, use 0~9 to input the user ID. Continuous press a number key to change the letter and press '#' key to confirm it.
- Set user password
Press 'SET/OK' to the submenu, use 'UP' and 'DOWN' to select 'User Password'. Press 'SET/OK', and then, use 0~9 to input the user password. Continuous press a number key to change the letter and press '#' key to confirm it.
|
|
